Oztec Gas Concrete Vibrator Honda 2.5 HP 2" Rubber Head 10' Shaft

Description

Oztec Gas Concrete Vibrator Honda 2.5 HP w/Quick Disconnect
With 2" Rubber Head and 10' Flexible Shaft
It must say "OZTEC" to be the industry's best concrete vibrator.
The BP-50a is equipped with a totally enclosed rotary throttle allowing the operator to comfortably control the engine while preventing we concrete from entering and clogging the throttle mechanism. A kill switch is also conveniently located in the same handle. The patented rotary throttle has been specifically designed and engineered to eliminate the operators variable setting of engine speed. This feature will ensure the the unit will consistently produce the proper vibrations per minute resulting in optimum concrete consolidation.
Powerful, portable and reliable…Oztec gas power units, provide ultimate and immediate adaptability on the job. Utilizing rugged and dependable Honda gasoline engines, coupled to our "speed-up" transmission, vibrator heads develop 12,000 vpm and never drop below 10,000vpm...Even in the heaviest low slump concrete loads. (Tested in near 0 slump concrete). This 10,000 - 12,000vpm range is essential for high-quality concrete. Direct drive units "scream", have short lives and usually drop below 10,000vpm when the head is immersed in concrete
Mounted on very comfortable frames, Oztec backpack power units allow operators incredible maneuverability around the job.
Oztec power units come standard with the Quick Disconnect "QD" system. Changing shafts and heads on the job is a snap.
Oztec Model No. BP-50A
Run time with full tank approximately 1 hour plus. .
Honda 1 3/4 HP,4 stroke engine
Runs vibrator heads 11,000 to 12,000 vpm
Comes standard with the Quick Disconnect "QD" system
Maximum Head Size 2.5" Steel 2.5" Rubber
Oztec units meet all United States OSHA and Canadian safety standards
Oztec's "High Efficiency RubberHead" Outperforms any other type of vibrator
Epoxy coated rebar presents a particularly troublesome problem. Steel heads act like an electric hammer, striking any rebar or forms they contact, over 10,000 times per minute, with a force from hundreds to over 2,000 pounds per blow. Contact with a steel vibrator head of as little as one second can chip enough coating to subject the steel to deep rust. Oztec's patented High Efficiency "RubberHead " vibrator head not only meets DOT non-metal head specifications for protecting coated rebar and expensive forms, but exhibit some very special and unique properties. The High Efficiency Rubber Head urethane dimpled construction sends strong shock waves off the entire length of the head, with a larger radius of action, producing denser concrete with less voids to patch.
Why the Oztec "RubberHead TM " outperforms any other type of Vibrator.
(a.) When a smooth vibrator head (round, square or any other shape) is lowered into a relatively stiff concrete batch, the front or nose of the vibrator drills a hole. It pushes away concrete faster than it can return. Result, shock waves produced mostly from the vibrator's front end.
(b.) Oztec's patented "RubberHead" has a large number of openings which allow wet concrete to cool the inner shell. These openings act like "suction cups", which keeps concrete in contact with the entire length of the vibrator head, sending strong shock waves into the mass.
Smooth vibrator head
Oztec's patented "RubberHead "
Eliminates damage to epoxy coated rebar caused by a standard steel vibrator head
Oztec's patented High Efficiency RubberHead
Will outperform any other type of vibrator…round, square, hi-cycle, etc…Any Type!
Will protect epoxy coated rebar and expensive forms.
Is outstanding in low slump (to "0" slump) concrete.
Essential in large pours of very stiff concrete.
Makes concrete denser with less voids to patch.
Vibrates at 12,000vpm, never drops below 10,500vpm when lowered deep into low slump concrete.
Provides Superior Action.
Is an absolute must for Architectural concrete where cosmetic surfaces are essential.
All Oztec vibrators meet or exceed ACI specification # 309
Radius of Action
-
The most important bit of information needed for complete consolidation
.
Radius of Action is the distance from the center of the vibrator to the outer edge, where complete consolidation takes place (see diagram).
For quality concrete Oztec lists conservative values for "Radius of Action". Complete consolidation is necessary for low slump concrete with close meshed reinforcement bars, high strength concrete and architectural concrete.
Radius of Action can be twice the listed values when slump is high or super plastisizers are used. It is important these values are used only as a general guide.
Kraft tool company manufactures superior quality concrete finishing tools made in the USA. As a trusted name in the concrete hand tool industry, Kraft Tool is proud of the
"Hand Krafted"
workmanship attributed to every product. Kraft Tool's product line is manufactured for everyday use for the professional cement finisher.
Concrete Curb, Gutter and Step Tools
Concrete Edgers and Groovers
Concrete Floats, Darbys & Tampers
Concrete Finishing Trowels
Knee Boards, Knee Pads & Acc.
Concrete Fresno's, Spreaders & Brooms
Concrete Tool Handles, Brackets & Adapter's
Concrete Restoration Tools
Concrete Power Equipment
Combined Shipping
We offer combined shipping on all our items. Shipping is combined based on the total weight of your order. To get combined shipping add all the items that you are interested in to your shopping cart and than click  Request total from seller.
Very Important
:
Please DO NOT pay for your order until the invoice is combined. If you pay for each item individually the orders will ship individually and will not be eligible for combined shipping.
International Customers
:
Please be aware of what your customs fees will be for your country before ordering. These fees are your responsibility and will have to be paid before your order will be released to you.
First Class Mail International:
shipping is the least inexpensive international shipping available, but keep in mind that in most cases orders do arrive within 20 business days, but some countries can take up to 90 business days to arrive. First Class Mail International tracking is limited to some countries and will not show no more once the order leaves the USPS facility in Chicago.